DMLS Cobalt Chrome(MP1)

Manufacturing Infomation

Pricing: $26.19/cm3
Minimum Cost:$88
Lead Time: 7 days
Max Print Size(mm):
250 x 250 x 280
Min Print Size(mm):
5 x 5 x 5
Layer Heights(mm):
Dimensional Accuracy:
±0.2% (with a lower limit of ±0.2 mm)
Smooth: 3/5
Detail: 4/5
Accuracy: 4/5
Rigidity: 5/5
Flexibility: 3/5


Suitable for:

  • Functional prototypes and end products
  • Cases, holders, adapters
  • Form and fit testing
  • Functional prototyping and testing
  • Not Suitable for:

  • Complex designs with intricate details
  • Fine-detail models with smooth surfaces
  • Moving and assembled parts
  • Large models
  • Cavities within design (unless making use of escape holes)
  • Colours Available


    Colours Post Process

    Polish, Sandblast

    Additional Info

    Parts built from EOS CobaltChrome MP1 conform to the chemical composition UNS R31538 of high carbon CoCrMo alloy. They are nickel-free (< 0.1 % nickel content) and are characterized by a fine, uniform crystal grain structure.

    As built EOS CobaltChrome MP1 meets the chemical and mechanical specifications of ISO 5832-4 and ASTM F75 for cast CoCrMo implant alloys, as well as the specifications of ISO 5832-12 and ASTM F1537 for wrought CoCrMo implants alloys except remaining elongation. The remaining elongation can be increased to fulfil even these standards by high temperature stress relieving or hot isostatic pressing (HIP).


    Additive Manufacturing

    Design Rules

    Min Supported Wall Thickness:0.9mm A supported wall is one connected to other walls on two or more sides.
    Min Unsupported Wall Thickness: 1mm An unsupported wall is one connected to other walls on less than two sides.
    Min Supported Wires:0.9mm A wire is a feature whose length is greater than five times its width. A supported wire is connected to walls on both sides.
    Min Unsupported Wires:1mm A wire is a feature whose length is greater than five times its width. An unsupported wire is connected to walls on less than two sides.
    Min Embossed Detail: 0.6mm A detail is a feature whose length is less than twice its width.
    The minimum detail is determined by the printer's resolution.When detail dimensions are below the minimum, the printer may not be able to accurately replicate them. Details that are too small can also be smoothed over in the polishing process.

    To ensure details come out clearly, make them larger than the indicated minimum. We may refrain from printing products with details smaller than the minimum, since the final product will not be true to your design. If your product has details smaller than the minimum, try making them larger, removing them, or considering a material with finer detail.
    Min Engraved Detail:0.6mm A detail is a feature whose length is less than twice its width. Engraved or debossed details go into a surface.
    Min Escape Holes:0mm
    Min Clearance:1mm Clearance is the space between any two parts, walls or wires. To ensure a successful product, make the clearance between parts, walls, and wires greater than the indicated minimum. If your clearance is too small, try making the gap bigger, or consider fusing the parts or features if their independence is unnecessary. You can also try a material with a smaller minimum clearance.
    Interlocking/moving or enclosed parts?No Sometimes the interlocking/moving parts can't be printed, since the supports inside the cross section can't be removed.
    Require Support Material?Yes Because each layer needs to build off the last, for some material, angles of more than 45 degrees generally require supports to be printed along with the design. Supports are not inherently detrimental for your design, but they do add complexity to the printing process and lead to less smooth finish on overhanging parts.

    Manufacture With This Material